Yellow — front left
On a left turn this is the inner front wheel. It has the larger steering angle and travels on the tighter of the two front-wheel paths. The path radius includes both the car's wheelbase and its sideways distance from O.
All wheel axes meet at one point → different radius, different angle
When a vehicle turns, the wheels cannot all follow the same circle. Each wheel is a different distance from the turn's instantaneous centre, so each traces a different radius. Ackermann steering makes the inner front wheel steer more sharply than the outer front wheel so both point in the directions needed for a clean, low-speed turn.
Ackermann steering geometry is the arrangement of the steering linkages that gives the front inside and outside wheels different steering angles. At low speeds, the ideal configuration makes the rolling directions of all four wheels compatible with one common instantaneous centre of rotation (ICR), located somewhere along the extended rear axle.
The wheel on the inside of the turn travels around a tighter circle; it must turn more. The outside wheel follows a wider circle and therefore needs a smaller steering angle. Real steering mechanisms approximate these relationships over a range of angles.
Each dashed circle is the ideal path traced by the centre of that wheel during a steady turn. It does not show the tyre's physical diameter or the car's swept body envelope. All four circles have the same centre O, but their radii differ.
The circles are stationary geometric loci in the diagram; their moving dashes and dots are animation cues. The outer wheel's dot has a greater linear speed because it covers more distance in the same turning time.
On a left turn this is the inner front wheel. It has the larger steering angle and travels on the tighter of the two front-wheel paths. The path radius includes both the car's wheelbase and its sideways distance from O.
On a left turn this is the outer front wheel. It steers less sharply, runs at a larger radius and must cover more ground per revolution of the car around O. On a right turn the inner and outer roles reverse.
On a left turn this is the inner rear wheel. Its path is the rear axle's shorter-radius circle. In this front-steering model the rear wheel's steering angle remains 0° even though its path curves.
On a left turn this is the outer rear wheel. It has the widest rear-wheel path and rolls farther than the inner rear wheel during the same turn. A differential allows the driven wheels to rotate at different speeds.
Angle is the wheel's heading relative to straight ahead, not the angle of its position around the turning circle. The rear wheels stay at 0° because this simulator models a conventional front-steered vehicle. Radius is the straight-line distance from O to the centre of that wheel; it is not the turning diameter.
At steering input 0°, all wheels travel in straight lines and their theoretical turning radii approach infinity.
The slider represents a virtual centreline steering angle, not the steering wheel's rotation or one physical tyre angle. Increasing that input moves O closer to the car and tightens every circle. Decreasing it pushes O farther away and enlarges them. Turning right mirrors the geometry.
The display uses a 2.8 m wheelbase and 1.6 m track width as illustrative dimensions.
R = L / tan(δ) • δinner = atan[L/(R − T/2)] • δouter = atan[L/(R + T/2)]
L = wheelbase (2.8 m); T = track (1.6 m); δ = virtual steering input; R = rear-axle midpoint radius. The front path radii are √[L² + (R ± T/2)²].With these dimensions, the reference steering input gives approximately 34.3° for the front left wheel and 26.1° for the front right. Their turning radii are 5.0 m and 6.4 m respectively. The straight rear wheels follow 4.1 m (left) and 5.7 m (right) circles. These readings update live above.
This is an ideal, planar, low-speed pure-rolling model. It excludes tyre slip angle, compliance, camber, caster, body roll, four-wheel steering and the fact that real linkage designs seldom match ideal Ackermann at every steering lock. At higher speeds, handling and tyre behaviour may call for a different steering relationship. Use the geometry as an educational demonstration, not a vehicle alignment specification.